the correct part is. 99 , at suzuki, see GM number far below.
SUZ, Part Number: 4342051860
that stud if snapped, would not stop wheel off
so if not stripped at stud to bolt juncture (look) the its stripped in the actual hub pressed in point, making the hub useless (IMO)
i guess your car has ABS, and matters big time here.
OP, G16 or J20 engine? GM shows same p/n for cars...
the problem here is what did they GM (GEO) put there new. ? or better, what's there now.
unified hubs started in 2001 (SUZ)
i bet it dont fit. for sure p/n are all different and ABS is a big problem.
2001+
Suzuki P/N is # 43401-65D00 (non/abs) or 65D10 suffix for ABS vehicles.
http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
other tricks, that can work.
when looking up parts on newer Trackers
pick not GEO but Chevrolet Tracker, to find parts,
you also have the huge problem of the funny GM wheel bearing hub locks there. (ended in 2001)
the unified hubs, fit unified spindles only
here is the part. ID 1;
99 G16 Vitara.
https://www.suzukicarparts.com/parts/199...CallOut=11
see parts 6 and 7, GM used differnt ,lock nuts there and funny tool to get in on and to get it back at 123 ft/lbs min. preload, (crush bearings they are, not like a boat trailer, at all)
see my page yet
old old page i made long ago.
http://www.fixkick.com/hubs/FW_BEARINGS.html
the gm link is there, but is under chevy no more GEO there. its chevy tracker.
http://www.gmpartsdirect.com/auto-parts/...embly-scat
and says not in stock
911-74733 (L/R)
1998 hub is
911-73635
is not the same.
finding aftermarket parts for suzuki can be impossible.
me guess, gets worse in time.
find one at a wrecker?
the problem is part 1 and 13 must match too. (no mixing , i bet)
in 2001 to 2005 all these parts changed, then again in 2006
http://www.fixkick.com/hubs/no-crush.JPG
SUZ, Part Number: 4342051860
that stud if snapped, would not stop wheel off
so if not stripped at stud to bolt juncture (look) the its stripped in the actual hub pressed in point, making the hub useless (IMO)
i guess your car has ABS, and matters big time here.
OP, G16 or J20 engine? GM shows same p/n for cars...
the problem here is what did they GM (GEO) put there new. ? or better, what's there now.
unified hubs started in 2001 (SUZ)
i bet it dont fit. for sure p/n are all different and ABS is a big problem.
2001+
Suzuki P/N is # 43401-65D00 (non/abs) or 65D10 suffix for ABS vehicles.
http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
other tricks, that can work.
when looking up parts on newer Trackers
pick not GEO but Chevrolet Tracker, to find parts,
you also have the huge problem of the funny GM wheel bearing hub locks there. (ended in 2001)
the unified hubs, fit unified spindles only
here is the part. ID 1;
99 G16 Vitara.
https://www.suzukicarparts.com/parts/199...CallOut=11
see parts 6 and 7, GM used differnt ,lock nuts there and funny tool to get in on and to get it back at 123 ft/lbs min. preload, (crush bearings they are, not like a boat trailer, at all)
see my page yet
old old page i made long ago.
http://www.fixkick.com/hubs/FW_BEARINGS.html
the gm link is there, but is under chevy no more GEO there. its chevy tracker.
http://www.gmpartsdirect.com/auto-parts/...embly-scat
and says not in stock
911-74733 (L/R)
1998 hub is
911-73635
is not the same.
finding aftermarket parts for suzuki can be impossible.
me guess, gets worse in time.
find one at a wrecker?
the problem is part 1 and 13 must match too. (no mixing , i bet)
in 2001 to 2005 all these parts changed, then again in 2006
http://www.fixkick.com/hubs/no-crush.JPG