Thanks for the help.
Okay, today I again dismantled ISC solenoid. Logically, the solenoid could not produce sufficient airflow, because the holes that I previously drilled on the gasket was too small. Now I have expanded the hole to the correct size. Now the solenoid is functioning properly. Hot idlle, now holds approx. 800 RPM. Turned on the lights, fan, etc.. holds about 950RPM. I'm also closed with silicone mass back side of the solenoid. Inside there is a screw to adjust. I tried to move the screw-it did not work, screw lot pinched or cemented factory. Maybe it's better not to touch.
Now ISC performs its function properly.
There is (perhaps) only one problem: In my country dayligtht is required by law, so my idlle still about 950 RPM always
But not a big problem.
Attached a few pictures from work. Perhaps someone help ...
![[Image: Fotografija0452.jpg]](http://s29.postimg.org/yenf1nfpv/Fotografija0452.jpg)
![[Image: Fotografija0453.jpg]](http://s29.postimg.org/71dmt5jrn/Fotografija0453.jpg)
![[Image: Fotografija0454.jpg]](http://s29.postimg.org/eirfm3yoj/Fotografija0454.jpg)
![[Image: Fotografija0455.jpg]](http://s29.postimg.org/br85vi05v/Fotografija0455.jpg)
![[Image: Fotografija0456.jpg]](http://s29.postimg.org/xmkr2gbir/Fotografija0456.jpg)
![[Image: Fotografija0457.jpg]](http://s29.postimg.org/avbog1qhf/Fotografija0457.jpg)
![[Image: Fotografija0458.jpg]](http://s29.postimg.org/703ozqhxv/Fotografija0458.jpg)
![[Image: Fotografija0459.jpg]](http://s29.postimg.org/yrjelkndf/Fotografija0459.jpg)
![[Image: Fotografija0460.jpg]](http://s29.postimg.org/cbn6y6teb/Fotografija0460.jpg)
Okay, today I again dismantled ISC solenoid. Logically, the solenoid could not produce sufficient airflow, because the holes that I previously drilled on the gasket was too small. Now I have expanded the hole to the correct size. Now the solenoid is functioning properly. Hot idlle, now holds approx. 800 RPM. Turned on the lights, fan, etc.. holds about 950RPM. I'm also closed with silicone mass back side of the solenoid. Inside there is a screw to adjust. I tried to move the screw-it did not work, screw lot pinched or cemented factory. Maybe it's better not to touch.
![Smile Smile](https://fixkick.com/forum/images/smilies/smile.gif)
![Smile Smile](https://fixkick.com/forum/images/smilies/smile.gif)
There is (perhaps) only one problem: In my country dayligtht is required by law, so my idlle still about 950 RPM always
![Smile Smile](https://fixkick.com/forum/images/smilies/smile.gif)
Attached a few pictures from work. Perhaps someone help ...
![[Image: Fotografija0452.jpg]](http://s29.postimg.org/yenf1nfpv/Fotografija0452.jpg)
![[Image: Fotografija0453.jpg]](http://s29.postimg.org/71dmt5jrn/Fotografija0453.jpg)
![[Image: Fotografija0454.jpg]](http://s29.postimg.org/eirfm3yoj/Fotografija0454.jpg)
![[Image: Fotografija0455.jpg]](http://s29.postimg.org/br85vi05v/Fotografija0455.jpg)
![[Image: Fotografija0456.jpg]](http://s29.postimg.org/xmkr2gbir/Fotografija0456.jpg)
![[Image: Fotografija0457.jpg]](http://s29.postimg.org/avbog1qhf/Fotografija0457.jpg)
![[Image: Fotografija0458.jpg]](http://s29.postimg.org/703ozqhxv/Fotografija0458.jpg)
![[Image: Fotografija0459.jpg]](http://s29.postimg.org/yrjelkndf/Fotografija0459.jpg)
![[Image: Fotografija0460.jpg]](http://s29.postimg.org/cbn6y6teb/Fotografija0460.jpg)
![[Image: Fotografija0461.jpg]](http://s29.postimg.org/uktyshydv/Fotografija0461.jpg)